Garland Gate Pros provides professional swing gates in Garland, TX for residential and commercial properties across the Dallas metroplex. Swing gates are the default across most of Garland. They need two footings rather than a run of concrete, they open fast, and the hardware stays adjustable for decades. What they need from us is a hinge post with an honest chance against the clay.
Everything about a swing gate is decided at the pier. We drill deep enough to carry the post below the layer that swells and shrinks, size the diameter to the leaf weight and the swing arm, and bell the bottom where the load justifies it. A post concreted eighteen inches into a hand-dug hole will lean within two seasons, and no hinge on the market will hide that.
Grade is the second question. Garland driveways often rise slightly from the street, and a gate that swings uphill needs ground clearance designed for the highest point in its arc, not the point where it sits closed. We measure the arc before fabrication. Where the rise is steep we use rising-butt hinges or shift the swing direction rather than trimming the bottom rail into a wedge. That measurement takes ten minutes and saves an expensive mistake.
Then the drive itself settles. Drop-rod holes drilled into a slab that later sinks a half inch stop lining up, and homeowners start lifting the rod by hand until they give up and leave the gate unlatched. We use adjustable drop rods with sleeves that can be reset, and on repeat offenders we relocate the receiver into a footing of its own. Relocating a receiver is a small job and it ends the problem permanently.
Hinge choice is not a place to save money. Sealed ball-bearing hinges on a heavy leaf outlast pin-and-strap by many years and keep the gate swinging with one finger, which in turn keeps the operator from working hard enough to break something. On dual swing entries we set both leaves independently so one can be re-plumbed without disturbing the other. Good hinges also make a manual push in a power cut something anyone can manage.
Numbers are useful here, so ask for ours. A twelve-foot steel leaf on a four-inch post generally gets an eighteen-inch pier taken seven to nine feet down in Blackland clay, belled at the base where the arm is long. A four-foot pedestrian gate does not, and we will not pretend it does. Pier size follows leaf weight times swing arm, not the fence line.
Most of our swing work is correction rather than new build. A gate that scrapes, will not latch, or bounces back off its stop is nearly always a plumb problem at the post. We re-set it, re-square the leaf, reset the operator force limits afterward, and the gate goes back to closing the way it did when it was new. It is the cheapest repair we offer and the one people put off longest.
With 15+ years of experience, our insured team brings the right materials and equipment to every job — wrought iron and ornamental steel fabrication, powder-coated aluminum gates, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, Class I-IV operator classifications, UL 325 entrapment protection — and backs the work with a written workmanship warranty. We serve Garland and nearby communities including Richardson, Mesquite, Rowlett, Plano.
What We Handle
Everything our swing gates in Garland covers
One crew, one point of contact, and the full range of swing gates work in Garland, TX. If it is on this list we do it in house rather than handing it to a subcontractor:
- swing driveway gates
- single swing gates
- dual swing gates
- swing gate operators
- articulated arm gate openers
- underground swing gate operators
- dragging swing gate repair
- swing gate hinge replacement
- swing gate post setting
- ball-bearing gate hinges
- cane bolt and drop rod sleeves
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Garland services.
Materials, equipment and how we do swing gates
The difference between swing gates that lasts and swing gates that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with wrought iron and ornamental steel fabrication, powder-coated aluminum gates, truck-rated cantilever slide gates, LiftMaster, DoorKing and FAAC operators, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Garland job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. 15+ years of gate work in the Dallas metroplex means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do swing gates outside Garland
Garland Gate Pros covers Garland and the surrounding communities of the Dallas metroplex. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Swing Gates in Richardson, TX — Dallas County, population 120,000
- Swing Gates in Mesquite, TX — Dallas County, population 150,000
- Swing Gates in Rowlett, TX — Dallas County, population 65,000
- Swing Gates in Plano, TX — Collin County, population 285,000
- Swing Gates in Sachse, TX — Dallas and Collin Counties, population 28,000
- Swing Gates in Wylie, TX — Collin County, population 60,000
Start on the Garland Gate Pros homepage for a free estimate, or call (877) 757-4456 and describe the job.
Why Garland Chooses Garland Gate Pros
- ✓Over 15 years installing and automating gates across the Dallas metroplex
- ✓In-house welding shop — we fabricate and coat our own gates rather than reselling panels
- ✓Deep footings engineered for North Texas blackland clay, so gates stay square
- ✓Every operator wired to UL 325 with photo eyes, loop detectors and tested entrapment protection
The standards behind swing gates
Quality here is not a matter of opinion — it is written down. The swing gates work we do in Garland follows published industry standards: DASMA is the standards body for door and access systems, and UL Solutions publishes UL 325, the safety standard for automatic gate operators. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every swing gates project in Garland gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (877) 757-4456 for a free swing gates free estimate in Garland, or request a quote and we'll get right back to you.