A cedar driveway gate costs $1,200 to $5,000 installed, with most single 12-foot gates on a steel frame landing between $2,000 and $3,500. Automation adds another $1,800 to $4,500. Width, height, and frame material are the three things that move the number.
Wood is the material people want and the material with the most ways to get it wrong. Almost all of them come back to the same thing: a gate is a lever, and wood on its own is not stiff enough to be the lever.
Where the price lands
| Configuration | Typical installed cost |
|---|---|
| Single 10–12 ft, wood frame, cedar | $1,200–$2,200 |
| Single 12 ft, steel frame, cedar cladding | $2,000–$3,500 |
| Dual swing, 14–16 ft total, steel frame | $3,000–$5,000 |
| Horizontal slat, premium grade cedar | Add 20–40% |
| Automation (operator, safety, power) | $1,800–$4,500 |
| Posts and footings, if not existing | $400–$1,500 |
The steel frame point, because it decides everything
A wood gate built entirely of wood will sag. Not might — will, on any span past about eight feet, because the joinery flexes under the weight of the panel hanging out from the hinge side.
People try to solve it with a diagonal brace, and on a narrow pedestrian gate that works. On a 12-foot driveway gate it delays the problem by a year or two.
The gates that last are welded steel frames with cedar cladding. The steel carries the load and holds the geometry; the wood provides the look. From two feet away you cannot tell, and the gate is still square in year fifteen.
If a quote for a wide wood gate does not mention a steel frame, ask what is stopping it from sagging. The answer will be informative.
Wind load: the thing nobody plans for
A solid privacy gate is a sail.
A 12-foot by 6-foot panel is 72 square feet of surface with nowhere for wind to go. That load goes into the hinges and then into the hinge post, in cycles, every windy day. It is the main reason solid gates work loose while picket gates do not.
Three ways to handle it:
- Spaced boards with a small gap between them, which barely changes the privacy at a distance
- A gap at the top or bottom of the panel to bleed pressure
- Size for it — heavier posts, deeper footings, heavy-duty hinges
Any of those is fine. Ignoring it is not, and in a windy market it is the difference between a gate that holds and a gate that develops a lean.
Species, honestly
Western red cedar is the default for good reason: naturally decay resistant, dimensionally stable, takes finish well, and light for its strength. Grade matters — clear or select tight-knot cedar stays much flatter than the knotty grades sold for fencing.
Redwood performs similarly where it is available and priced sensibly.
Pressure-treated pine costs less and moves more. On a fence, a twisted board is a fence board. On a gate, it is a visible defect on a panel you look at every time you come home, and the movement stresses the fasteners.
Ipe and other hardwoods are gorgeous, extremely stable, extremely heavy, and expensive enough that most people stop after the quote. On an automated gate the weight is a genuine consideration.
Finish, and what happens if you skip it
Plan on a penetrating stain or oil every two to three years, more often on a west-facing gate.
The important part is less obvious: finish all six faces of every board, including the end grain, before assembly. End grain absorbs moisture far faster than face grain, and unsealed board ends are where cupping and rot start. A gate that was finished after assembly has unsealed end grain hidden inside every joint.
If you would rather not maintain it, let cedar weather naturally to silver-gray. That is a legitimate choice and a lot of people prefer the look. Just know that unfinished wood cycles moisture harder and moves more, which is another argument for the steel frame.
The bottom rail is where wood gates die, same as steel gates. Keep it up off the ground, keep sprinklers off it, and keep debris from piling against it.
Automation with a wood gate
Doable and common, with two conditions.
Steel frame, as above. A wood-framed gate under a motor works itself out of square.
Correctly sized operator, accounting for both the weight of solid cedar and the wind load. A solid wood gate is one of the heavier residential gates, and an operator running at its rated limit is an operator with a short life. Our gate opener cost guide covers sizing and what the safety devices add.
Also worth thinking about which way it swings and whether the driveway slopes — a solid wood gate has no clearance to spare. Our sliding versus swing comparison covers that decision.
When wood is the wrong call
We build wood gates and we will still say it.
Full afternoon sun on a west-facing entrance is hard on any finish. You are signing up for a more frequent refinishing schedule than the brochure implies.
Sprinkler overspray hitting the gate daily will rot the bottom rail regardless of species. Move the head or pick a different material.
A gate that cycles thirty times a day is a lot of mass to move repeatedly. Aluminum or ornamental steel handles high duty cycle better — see our aluminum versus iron comparison.
If you want zero maintenance, buy metal. Wood is a material you have a relationship with. Some people enjoy that. If you know you will not, do not pretend otherwise at the quote stage.
What you can do yourself
Refinishing is a genuine DIY weekend. Clean, let it dry fully, sand any rough areas, and apply a penetrating stain. Materials are under $100 for a typical gate, and doing it on schedule doubles the life of the wood.
Replacing individual boards on a steel-framed gate is straightforward — match the profile, use exterior-rated fasteners, seal all six faces before installing.
Do not DIY the frame, the posts, or the operator. The frame is welding, the posts are concrete and geometry, and the operator has safety requirements that are not a place to improvise.
Garland Gate Pros builds wood driveway gates on welded steel frames, installs automatic openers sized to the weight, and handles matching security fencing across Garland and the Dallas metroplex. For overall pricing, see our driveway gate cost guide.
Get a free quote → · call (844) 511-2320
Ready for a free quote in Garland?
Garland Gate Pros — free estimate, clear scope, no pressure. Use the form on this page or jump to the homepage quote.
Related services in Garland
Garland Gate Pros money pages — go straight to the service you need.
- Wood Gates →
Wood driveway gates read warm in a way metal never manages, and a horizontal-slat cedar gate against a modern brick elevation still beats anything else on the street. The catch is that wood on its own will not hold a fourteen-foot span square through one Texas summer, which is why every wood gate we build in Garland hangs on a welded steel frame.
- Automatic Gate Operators →
Automatic gate operators are what separate an entrance you actually use from an expensive fence panel you leave propped open, and they are the single most commonly undersized line on a gate quote. We install and repair LiftMaster, DoorKing, FAAC, Ramset, and Apollo swing and slide operators throughout Garland and the metroplex, matched to the real weight, span, wind exposure, and daily cycle count of the gate they are driving.
- Security Fencing & Perimeter →
Security fencing is what makes a gate mean something, because an impressive entrance next to a leaning chain-link run is an expensive arrow pointing straight at the weak spot. We fabricate and install matching wrought iron, ornamental steel, and aluminum perimeter fencing around Garland that ties into the gate so the whole line reads as one piece of work rather than two projects done years apart.
- Wrought Iron Gates →
Wrought iron gates are still the entrance most Garland homeowners have in mind when they start looking, and out on an open North Texas lot they have the useful property of not caring how hard the wind is blowing. We forge and weld custom wrought iron and ornamental iron driveway gates in our own Garland shop from solid bar and heavy-wall tube, never the thin decorative stock that dents if a mailbox looks at it sideways.
- Ornamental Steel Gates →
Ornamental steel gates deliver most of the presence of wrought iron at a friendlier price, and when they are hot-dip galvanized before coating they will outlast the concrete they sit on. We fabricate ornamental steel driveway gates in Garland from 14-gauge and 16-gauge tube sized to the actual span, with fully welded corners instead of the bolted brackets that come on prefabricated big-box panels.
Frequently asked questions
How much does a cedar driveway gate cost?
Most cedar driveway gates run $1,200 to $5,000 installed depending on width, height, and whether the frame is wood or steel. A single 12-foot gate on a steel frame with quality cedar typically lands around $2,000 to $3,500. Automation adds $1,800 to $4,500 on top.
Why do wood driveway gates sag?
Because a wide wood frame cannot resist the diagonal load of its own weight. A gate is a lever, and wood joinery flexes. The fix is a welded steel frame with cedar cladding on it — the steel carries the structure, the wood does the looking. Almost every long-lasting wood gate is built that way.
Is cedar better than redwood or pressure-treated pine for a gate?
Cedar and redwood both have natural decay resistance and stay stable, and either will serve 15 to 20 years with care. Pressure-treated pine costs less and warps considerably more, which on a gate matters far more than on a fence, because a twisted board on a moving panel is visible every day.
How often does a wood gate need refinishing?
Every two to three years for a penetrating stain or oil, more often on a west-facing gate that takes full afternoon sun. Left unfinished, cedar weathers to silver-gray, which some people want. It is not just cosmetic though — unfinished wood cycles moisture harder and moves more.
Can a wood gate be automated?
Yes, on a steel frame. Solid wood panels are heavy and they catch wind like a sail, so operator sizing matters more here than with an open picket gate. A wood gate on a wood frame is a poor automation candidate because the frame flexes and the operator wears it out of square.
Does a solid wood gate have wind problems?
Yes, and it is the most underestimated issue with privacy gates. A solid 12-by-6-foot panel is 72 square feet of sail on a hinge post. In a windy market, either build in a top or bottom gap, use spaced boards, or size the posts and hinges for the load. Do not let anyone hand-wave this.
Local context
How this applies in Garland, TX
Every article here is written from gate work done in Garland and the Dallas metroplex, so the numbers reflect local labour, permit and material costs rather than a national average. Your own job can land either side of them depending on access, the condition of what is already there, and the materials you pick — wrought iron and ornamental steel fabrication, powder-coated aluminum gates, truck-rated cantilever slide gates.
The way to turn any of this into a real answer is to have someone look at your actual situation. The free estimate is free, itemized and written down, with no deposit and no obligation. Call (844) 511-2320 or start on the Garland Gate Pros homepage.
Areas Garland Gate Pros covers
Garland first, then the surrounding communities of the Dallas metroplex. Each has its own page with local detail rather than a copy of this one:
- Richardson, TX — Dallas County, population 120,000
- Mesquite, TX — Dallas County, population 150,000
- Rowlett, TX — Dallas County, population 65,000
- Plano, TX — Collin County, population 285,000
- Sachse, TX — Dallas and Collin Counties, population 28,000
- Wylie, TX — Collin County, population 60,000
Or jump to the full list of Garland services.
The Garland Gate Pros Team
Licensed gate pros in Garland, TX
Written by the Garland Gate Pros team — licensed, insured gate pros with 15+ years serving Garland, TX and the surrounding area.